You can use any brand nails as long as they are the same degree as your nailers and are within the length set for your gun.
Will Paslode nails work in a DeWalt nail gun?
The DW nails are fully compatible with Paslodes, etc and the DW in turn will happily use gas nailer nails as well. So if you can get nails that will fit a Paslode IM350, then they will also fit the DW.
Are Paslode nails universal?
Universal, clipped head nails for use in Paslode IM350/IM350+ and other brand gas nailers. …
How many nails are in a paslode strip?
When you buy a fastener pack they contain 2500 nails and, yes, they give two fuel cells with it. The nails are paper-collated and at an angle (34˚), and come in three different coatings/finishes: bright, hot dip galvanised, and mechanically galvanised – all with diamond points.
What nails can I use in a DeWalt nail gun?
Nails. The DeWalt nailer takes 2″ to 3.5″, 30 or 34 degree angled, paper tape nails, with either clipped or offset, full-round heads.
What nails does the DeWalt DCN692 use?
DeWalt Galvanised Ring Nails are a range of steel nails tested to work with the DeWalt DCN692 framing nailer, guaranteeing the best level of performance between the nails and gun. Although it has been tested with DeWalt products, these nails can be used with a multiple amount of nailers.
What nails fit DeWalt 2nd fix nail gun?
The more popular brands of 2nd fix nail guns such as Paslode, Dewalt, Senco, Tacwise and Hitachi tend to favour 16 gauge or 18 gauge nails, with 18g being the finer of the two. 16 gauge nails cannot be used in 18 gauge nailers and visa versa.
Can I use finish nails in a brad nailer?
Brad nails are formed from a fine, 18-gauge wire, which means they are smaller in diameter and typically have less holding strength. The benefit to an 18-gauge brad is its size. … Finish nailers will run 15- or 16-gauge finish nails, in both angled and straight varieties depending on the tool.
What nails can you use in Bostitch nail gun?
We carry just about every type of nails available for each manufacturer named above. Our nails for Bostitch include pin nails, brads, straight finish nails, angled finish nails, hardwood flooring cleats, round head framing nails, stick nails, metal connector nails, coil sliding nails and coil roofing nails.
Will Bostitch nails fit Hitachi?
Other brands that will fit are: Stanley Bostitch, Accuset, Duofast, Campbell Hausfeld, Hitachi, Atro, Paslode, Porter Cable and DeWalt. 1 of 1 found this helpful.
Will Paslode fuel cells work in Hitachi framing nailer?
As long as the Paslode cartridge box states that they are compatible with the Hitachi NT65GB nailer, they will work fine. If not, compare the cartridges – if they’re the same size, they’ll be fine.
Can you use other nails in paslode?
As far as I know only Paslode Roundrive will fit the Im90 and any other nail will not work right. The Roundrive have a full round head wheras any other on the market have D heads. You will find the firing pin will hit one Roundrive bang on wheras it will hit two clipped head nails at the same time.
Does DeWalt make a nail gun?
The DEWALT DCN680 18 Gauge Brad Nailer drives 18 Gauge brad nails from 5/8-inch to 2-1/8-inch which makes it ideal for fastening decorative molding, casing, kitchen crown, and shoe molding.
Can a DeWalt nail gun use staples?
Heavy duty hand tacker built for the jobsite. Fires DeWalt, Arrow or Stanley heavy duty staples and 18 gauge brads.
Can I use DeWalt nails in a Bostitch nail gun?
Any brand will work, just make sure get the correct size and angle if needed.
Can DeWalt finish nailer use staples?
The DEWALT Heavy-Duty Staple/Nail Gun can use a wide variety of staples and 18-Gauge steel brad nails. This gun features bottom loading and a steel magazine for quick and easy reloading. The gun’s steel handle is covered by a molded grip to help provide comfortable usage.
How long do Paslode fuel cells last?
Paslode fuel cells have a long shelf life with the inbuilt design and metering valve system enabling the product to be stored for about 27 months.
Why does my paslode not fire?
Possible causes for a Paslode nail gun not firing are: A nail jam is stopping the nails from moving forward. The gas fuel cell is empty, out-of-date or not attached properly. … The nailer needs cleaned – especially if it has been used a lot without regular cleaning!
Are Paslode nails 10D?
Paslode 3″ x 0.131″ 10D Coated Round Head Nail 2500/box.
What size nails should I use for framing?
Nail size is more important than you might think when framing interior walls. Nails that are too long or fat are difficult to drive and can split wood, while short or thin nails just don’t do the job. The best nails for framing are 3 1/2 inches long. These are called 16-d, or “16-penny,” nails.